The lingual concavity is a hollow or depression on the inner surface of the back of the lower jaw, below the ridge crest, and it is the usual route for a lingual plate perforation. It is common, it cannot be seen on an OPG or periapical, and a deep one changes the safe angle and length of an implant. A cross-sectional CBCT view is needed to see it.
Most Implantologists planning a lower molar implant look at the height above the canal first. The concavity is the second hazard in the same site and the one more often missed, because a flat image shows height and the ridge crest, and the problem lies in the shape of the bone below it. This article describes what it is, how common it is, what goes wrong and why 2D imaging under-estimates it. It describes the hazard, not a measurement protocol.
What the Lingual Concavity Is
The posterior mandible is not a block of bone with a flat inner wall. Below the mylohyoid line, the lingual surface can curve inwards, so the bone is narrower in its lower part than at the crest. An implant placed along the line suggested by the crest can then run towards the lingual cortex as it goes deeper. The deeper and steeper the hollow, the less margin there is.
How Common Is It?
The studies that have examined this with CBCT agree that some concavity is common and that a deep one is a minority:
In a CBCT study of 164 patients, the lingual undercut shape was the most common ridge form at the first molar site, found in 50% of scans. Among those, about 71% were deeper than 2 mm, and the depth ranged from under 1 mm to nearly 5 mm.
In a study of 826 posterior mandibular sockets, 93% had a concavity of some degree, and 26% had a deeper one, with an angle below 60 degrees. About 1% were extremely deep, below 40 degrees. The authors concluded that only a few cases carry a high risk of lingual plate perforation.
An earlier cross-sectional CBCT analysis of the mandibular concavity, by Chan and colleagues, reported the same pattern and concluded that a concavity needs to be considered before placing an implant.
Numbers differ between studies because definitions, sites and populations differ. The practical point is that most posterior mandibles have some concavity, a quarter have a significant one, and a few have a very deep one. You cannot tell which group a patient belongs to without looking in cross-section.
What Goes Wrong
Lingual plate perforation. The implant or drill exits through the inner cortex.
Bleeding in the floor of the mouth. The soft tissue beside the lingual plate contains blood vessels. Case reports describe serious floor-of-mouth haematoma with airway compromise after lingual perforation in the posterior mandible; add a verified reference here.
A bicortical or exposed implant that cannot be covered by bone and fails or needs removal.
Nerve involvement. The canal and the lingual nerve lie close, and the angle chosen to avoid one can bring the drill closer to the other.
Most cases are uneventful, and it is the rare serious complication, bleeding that threatens the airway, that makes the concavity worth knowing about. Why implant failures happen places it among the avoidable imaging mistakes.
Why a 2D Image Under-Estimates It
| Image | What it shows | What it cannot show |
|---|---|---|
| Periapical | Height, root position and bone density in a small area | Any information about thickness or shape from cheek to tongue |
| OPG | Overall height and the canal outline, with magnification | The inner surface of the jaw and the shape of the ridge in cross-section |
| CBCT cross-section | The shape of the ridge from cheek to tongue, the concavity and the canal position | Soft tissue vessels directly, and fine bone detail where artefact is present |
The concavity sits in the plane that flat images collapse. On an OPG the lingual cortex is not visible as a surface, so a ridge that looks sound in height can be narrow and sloping in the apical third. OPG and CBCT: which does the patient need explains the difference in general terms.
What the Scan Report Should Say
Whether a lingual concavity is present at the planned site, and where in the ridge it lies.
Whether it is mild, moderate or deep, with the sections it was seen on.
The canal position in relation to the concavity.
Any limitation, such as artefact from nearby metal.
A report that gives height above the canal and nothing about the cross-sectional shape has answered half the question. How to read a CBCT report explains what a complete one contains.
Planning Implications, Not a Method
A deep concavity does not rule out an implant. It changes the choices: the angle of the osteotomy, the length of the implant, the position of the platform, the need for a guide, or a different approach such as a shorter implant or a grafting step. Those choices belong to the operator, who has the scan, the patient and the surgical plan in front of them. For structured training in reading the scan for these decisions, the CBCT implantology course covers it.
Frequently Asked Questions
-
A hollow on the inner, tongue-side surface of the lower jaw below the ridge crest, mainly in the molar region. It makes the bone narrower lower down than at the crest.
-
No. An OPG shows height and outline but not the inner surface or the shape of the ridge in cross-section.
-
The implant or drill can exit through the inner wall, with a risk of bleeding in the floor of the mouth and an implant that is not fully covered by bone.
-
No. It changes the planning choices, such as angle, length and position, and sometimes the approach.
-
A cross-sectional view is the way to see the ridge shape and the canal together, so a CBCT is commonly used for planning.